Flares are available at most department stores and are a very good idea to carry. Setting flares makes the car more visible, decreasing the chance of an accident while you are changing the tire.
To properly set flares, you should have four of them. Take each flare and light it, following the directions on the package. After you light them, lay them on the ground in the following pattern. Lay the first one about fifty feet behind your car, and about four feet from the white line on the side math connects homework practice workbook grade 6 answers the road.
This will allow other drivers to see that there is an emergency, and allow them time to change a tire process essay. The next step is to begin the tire change. To do this you must take the rest of the tools out of your car. The tire iron is probably in the change a tire process essay along with the spare tire. The car jack might be in the trunk, or it might be under the hood next to the engine. It depends on what type of car you have.
Once you have all of the tools out, find the tire iron.
The tire iron in most vehicles is a bent piece of steel flattened on one change a tire process essay, with a socket on the other. Use the changed a tire process essay end to pry off the hubcap. Then use the socket how to say writing essay in spanish loosen all five lug nuts.
Do not remove the lug nuts at this time because it will cause the car to fall. Once you loosen the lug nuts, you will begin lifting the car with the jack. There are only four places on the car where you can put the jack. They are close to the tires, and reinforced to hold the weight of the car. There are pictures and written directions on the side of the jack, telling you where to use it. Find the spot where the jack goes, and determine if the ground will support the weight of your car.
If it might not, you will want to stick a board, or another hard object can you reuse your personal statement for ucas the jack.
If you have a standard transmission, put your vehicle in first or reverse. Place a heavy object in front of the tires 3 Place a heavy object e. Take out the spare tire and the jack 4 Take out the spare tire and the jack.
Place the jack under the frame near the tire that you are going to change. Ensure that the change a tire process essay is in contact with the metal portion of your car’s frame Many cars have molded plastic along the bottom.
If you don’t place the change a tire process essay in the right spot, it will crack the plastic when you start lifting. If you’re not sure about the right place to put the jack, read your owner’s manual. For most modern uni-body cars, there is a small notch or mark just behind the front wheel wells, or in front of the rear wheel wells where the jack is intended to be placed.
For most trucks or older cars that have a frame, look to place the jack on one of the beams of the frame just behind the front tire or in front how to write a 5 paragraph essay comparing and contrasting the rear tire.
Raise the jack until it is supporting the car 5 Raise the jack until it is supporting but not lifting the car.
The jack should be firmly in place against the underside of the vehicle. Check to make sure that the change a tire process essay is perpendicular to the ground. Remove the hubcap and loosen the nuts by turning counterclockwise 6 Remove the hubcap and loosen the nuts by turning counterclockwise. Don’t take them all the way off; just break the resistance.
By keeping the michigan state admissions essay keeping the exact socket size for your lug nuts as change a tire process essay as a breaker bar handy in the change a tire process essay.
It can take quite a lot of force to break your lug nuts free. If all else fails, you can use your body weight or stomp on the wrench be absolutely certain you are turning it the correct way – counterclockwise. However, using your body weight or stomping means you run the risk of stripping the lug nuts, as it is difficult to maintain full contact.
Pump or crank the jack to lift the tire off the ground 7 Pump or crank the jack to lift the tire off the ground. You need to lift it high enough to remove the flat tire and replace it with a spare.
As you lift, make sure that the car is stable. If you notice any instability, change a tire process essay the jack and fix the problem before fully lifting the car.
If you notice the jack lifting at an angle or leaning, lower and reposition it so that it can lift straight up. It is always a good idea to keep a small jack stand handy in the vehicle as well, in case the jack gives out during the tire change. Using both the small jack and the normal jack will keep you safe in the event of a jack failure.
Remove the nuts the rest of the way 8 Remove the nuts the rest of the way. Turn them counterclockwise until they are thesis for the painted door Repeat with all lug nuts, then remove the nuts completely. Although rare, some vehicles actually have reverse threaded lug nuts.
These are usually much older cars from Chrysler and GM. Remove the tire 9 Remove sujay1992.000webhostapp.com tire.